Akai MPC5000 Specifications download pdf (Page 127)

113

Tip: If you want to retry dividing a sample, press the [F5] (RECHOP) button. The 'Chop Shop' window will be displayed

and you can set it again. If you want to stop the 'Chop Shop' feature, press the [F1] (CANCEL) button. The display will

go back to the 'TRIM' page.

02. In the 'Region' field, select the region number you wish to adjust the start/end point.

In the image above, region 1 is selected.

03. In the 'St' field, adjust the start point of the region.

You can change the start point by using the numeric keys directly or by turning the [DATA] wheel button. If you press the left/right cursor key while

holding the [SHIFT] button, you can select individual digits to change with the [DATA] wheel.

Note: Each start point of a region is same as the end point of the previous region. If you change the start point of a

region, the end point of the previous region will be changed automatically.

04. In the 'End' field, adjust the end point of the region.

You can change the end point the same way as the start point.

Note: Each end point of a region is same as the start point of the next region. If you change the end point of a region,

the start point of the next region will be changed automatically.

If you press the [F6] (EDIT) button, the Region Edit window will be displayed. You can extract, divide, or combine regions in this page. Refer to

'Editing a Patched Phrase'.

If you wish to cancel the Chop Shop function, press the [F1] (CANCEL) button. The TRIM page will be displayed.

 Zoom

With the Chop Fine window, you can zoom in to a Chop Point and edit it

in detail. While Chopping a sample, select the region you would like to

edit, place the cursor in either in the 'St' (Start) or 'End' field, and press

the [WINDOW] button. The Chop Fine window will be displayed.

In the Chop Fine window, the waveform display varies depending on the

location of the cursor. When you select the 'St' (Start) field with the

cursor, it displays the start point in the center of the window. When you

select the 'End' field, it displays the end point in the center.

If you press the [F2] (ZOOM-) button the waveform will be zoomed out,

if you press the [F3] (ZOOM+) button, it will be zoomed in.

LINEAR and LOGARITHMIC displays

The vertical axis indicates the sample’s level. Normally, the waveform display is set to LINEAR, which displays the sample level as it

is. However, some parts (fade out part etc…) may not be displayed in the waveform if the level is too low. In this case, you can switch

to the LOG (logarithmic) display by pressing the [F5] (LOG) button and you can see the parts whose level is low. When you switch to

the LOG mode, the display in the [F5] button will change to LINEAR. To switch back to the LINEAR mode, press the [F5] button again.

 Converting Divided Samples to SLICED SAMPLES

01. After adjusting the parameters within each region, press the [F4] (CONVRT) button.

The Convert window will be displayed. Here you can select two different ways for converting the divided sample, SLICED SAMPLE or PATCHED

PHRASE

02. In the 'Convert to' field, select SLICED SAMPLES.

Release

This sets the length that is added to the release after dividing a sample.

If you set this to larger value, the release of the divided sample will be

long and the sample data will be larger in size as well.

Create New Program

If you set this to YES, the MPC5000 makes a Program where each

region is assigned to pads, from PAD A01 – A16, in order.

03. After adjusting each parameter, press [F5] (DO IT).

The MPC5000 will process the SLICED SAMPLES and then the 'TRIM' page, with

the divided sample, will be displayed.

The new sample name of the divided sample will be the original sample name and a number.

1 2 ... 122 123 124 125 126 127 128 129 130 131 132 ... 221 222

Akai MPC5000 Specifications Page 127

Comments to this Manuals

Akai MPC5000 Specifications Page 127

Comments to this Manuals

Related products and manuals for Musical Instruments Akai MPC5000