Akai MPC STUDIO Datasheet download pdf (Page 9)

26. SEQ EDIT / EFFECTS – Press this button to enter Sequence Edit mode. Hold down SHIFT and press this

button to enter Effects mode, where you can select and route effects as well as edit effects' parameters.

27. SAMPLE EDIT / SAMPLE REC – Press this button to view the Sample Edit screen in the display and

software. Hold down SHIFT and press this button to view the Sample Record screen in the display and

software.

28. SONG / OTHER – Press this button to view the Song screen in the display and software. Hold down SHIFT

and press this button to enter Other mode, which allows you to set: the minimum number of taps for the

TAP TEMPO button; pad threshold, sensitivity, and curve; the footswitches' messages; and the Program

Change target.

29. STEP SEQ – Press this button to view the Step Sequence screen in the display and software.

30. NEXT SEQ – Press this button to view the Next Sequence screen in the display and software.

31. TRACK MUTE / PAD MUTE – Press this button to view the Track Mute screen in the display and software.

Hold SHIFT and press this button to view the Pad Mute screen in the display and software.

32. WINDOW / FULL SCREEN – When this button is lit, it means the selected field in the display contains

additional functions; press this button to access them. Use the F-BUTTONS, CURSOR BUTTONS, and

DATA DIAL or -/+ buttons to execute (or cancel) these additional functions.

Hold SHIFT and press this button to switch between Full Screen and Half Screen modes. In Full Screen

mode, the workspace occupies the whole screen. In Half Screen mode, the parameter controls (Q-Link

knobs, pads, Sequence and Track information, Project Information, etc.) are shown underneath the

workspace.

33. PROJECT / FOLDER 1 – Press this button to view only Project files in the File Browser. Hold down SHIFT

and press this button to select the Browser's Folder 1 shortcut.

34. SEQUENCE / FOLDER 2 – Press this button to view only Sequence files in the File Browser. Hold down

SHIFT and press this button to select the Browser's Folder 2 shortcut.

35. PROGRAM / FOLDER 3 – Press this button to view only Program files in the File Browser. Hold down

SHIFT and press this button to select the Browser's Folder 3 shortcut.

36. SAMPLE / FOLDER 4 – Press this button to view only Sample files in the File Browser. Hold down SHIFT

and press this button to select the Browser's Folder 4 shortcut.

37. NO FILTER / FOLDER 5 – Press this button to view all files in the File Browser. Hold down SHIFT and

press this button to select the Browser's Folder 5 shortcut.

TRANSPORT / RECORDING CONTROLS

38. PLAY – Press this button to play the Sequence from the audio pointer's current position.

39. PLAY START – Press this button to play the Sequence from its start point.

40. STOP – Press this button to stop playback.

41. REC – Press this button to record-arm the Sequence. Press PLAY or PLAY START to start recording.

Recording in this way (rather than using OVERDUB) erases the events of the current Sequence. After the

Sequence plays through once while recording, Overdub will be enabled.

42. OVERDUB – Press this button to enable Overdub, which allows you to record note events in a Sequence

without overwriting any previously recorded note events. You can enable Overdub either before or during

recording.

43. < / > ( |< / >| ) – Use these buttons to move the audio pointer left/right, one step at a time. Hold LOCATE

and press one of these buttons to move the audio pointer to the previous/next event in the Sequence Grid.

44. << / >> (START/END) – Use these buttons to move the audio pointer left/right, one bar at a time. Hold

LOCATE and press one of these buttons to move the audio pointer to the start or end of the Sequence

Grid.

45. GO TO – Hold this button down to activate the secondary functions of the < / > and << / >> buttons (i.e., |<

/ >| and START/END, respectively).

46. ERASE – As a Sequence is playing, hold this button down and press a pad to delete the note event for that

pad at the current playback position. This is a quick way to delete note events from your Sequence without

having to stop playback.

47. TAP TEMPO – Press this button in time with the desired tempo to enter a new tempo (in BPM) in the

software.

SUPPORT & UPDATES

For additional information, technical support, and the most current versions of software, firmware, or drivers,

please visit:

www.akaipro.com/mpcstudio

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 39 40

Comments to this Manuals

No comments

Akai MPC STUDIO Datasheet Page 9

Comments to this Manuals

Related products and manuals for DJ controllers Akai MPC STUDIO