Akai ACAD100N Technical Information Page 6

  • Download
  • Add to my manuals
  • Print
  • Page
    / 38
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 5
6
 Before the final installation of the device into a DIN
insertion compartment in the dashboard, connect the
cables and test the connections.
 Only use the accessories included in the delivery.
Usage of unauthorized components can cause
damages.
 If you need to drill holes or make other changes for
the installation, consult a specialized workshop in
your area.
 This device is designed for a vehicle power supply of
12 V with the ground on the car body (negative pole).
Check the battery voltage before installing it into a
camping vehicle, bus, or truck.
 To avoid short circuits, the battery has to be
disconnected before the installation.
 Read the guidelines in this handbook for the
connection of the power supply.
 Secure the installed cables with insulating tape, cable
ties, or cable clamps. To protect the cables from
damage, use insulating tape when guiding them past
metal components. Place and secure all cables in
such a manner that they are not in the vicinity of
movable parts, such as e.g. the parking brake, gas/
brake/coupling pedals, handle bars and seat tracks.
 Do not place any cables in the vicinity of heat sources
(e.g. near the heater ventilation), since the insulation
of the cables might get damaged and result in short
circuits.
 Do not short circuit any cables. This can result in
damages to the vehicle and device.
 Never establish a power supply to other devices by
removing the insulation of the device’s power supply
and connecting an additional cable. Otherwise, the
maximum power rating of the cable will be exceeded
and there will be a danger of overheating.
 If you have to replace the fuse, only use an identical
one with the same rating.
 The connected speakers have to be high-
performance speakers with a minimum output of 40 W
and an impedance ranging from 4 to 8 ohm. If you
connect speakers with other output or impedance
ratings, the speakers may burn, smoke, or sustain
other kinds of damage.
 When the device is turned on, a control signal adjoins
the blue cable of the connection A5 (ISO plug A). You
can connect this to the relay of the extendable vehicle
antenna (max. 100 mA, 12 V). If your vehicle has a
wire antenna inside the windshield, connect the blue
cable A5 (ISO plug A) to the pre-amplifier of the
antenna.
 If an external audio amplifier is connected to the
device, the blue cable of connection A5 (ISO plug A)
may not be connected to the power supply of the
amplifier. Likewise, you may not connect it to the
power supply of an active car antenna. This poses a
risk of short circuits and malfunctions.
 Insulate unused connection cables with insulating
tape. The same applies to unused speaker cables.
Otherwise there is a risk of short circuits.
 Dirt or condensed moisture on the lens of the CD/
DVD drive may impede and even prevent the
playback of data carriers.
 In general, the playback of self-burned data carriers is
possible, but it depends on the used software and the
settings made with it, so that there may be problems
during playback in individual cases. You can receive
further information from the manufacturer of your
software
 Additional CD data carriers can be played back just
like audio CDs. It’s possible that CD-R/CD-RW data
carriers can’t be played back correctly if they were
recorded by a device other than an audio CD
recorder.
 In addition, it may be the case that a data carrier
(CD-R/CD-RW) recorded with an audio CD recorder
can’t be played back due to the conditional features,
irregular formats, or soiling of the data carriers.
 The information recorded on the data carrier
(ID3TAG) is displayed by this device.
 After inserting a CD-RW data carrier, it takes a little
longer for the playback to begin than with regular CD
or CD-R data carriers. Also read the guidelines on the
sleeves of the CD-R/CD-RW data carriers before you
insert them.
 Do not turn on or off the product in short intervals.
When turning the unit off, wait for at least 10 seconds
prior to turning the unit on again. Do not operate the
player with scratched, bended or broken discs and
when a disc is not loaded properly, do not force it into
the player.
 Do not UPDATE the unit in the SETTING menu by
yourself until contacting with your supplier. If your unit
is working abnormally, please contact with your
supplier first and let them decide whether it can be
modified by software updating.
NOTE
 Please dispose of empty batteries according the
regulations in your country.
 All On Screen Displays (OSD) and Pictures will be
based on the English version.
 Design and Specifications may vary in the manual
from the actual product in use.
Page view 5
1 2 3 4 5 6 7 8 9 10 11 ... 37 38

Comments to this Manuals

No comments