PIONEER’The Art of Brt&tainmentOperating ir^tructions Mode cfemploiRMD-V3104UMULTI VIDEO PROCESSOR 1-lnput 4-Output (NTSC)PROCESSEUR VIDEO MULTI S
CONTROLS AND CONNECTORS(0) OPTION video input connectorsThese input connectors are used when an option board is installed.When the RMD-V302
OPTION BOARD RMD-V3020 (VARIABLE SCAN BOARD)1. Features(1) Large-screen computer imagesBy adding the optional RMD-V3020 (variable scan board)*
TROUBLESHOOTINGWhat seems to be a malfunction is not always so. In case of trouble, first check the list of common problems in t
SPECIFICATIONSMulti-Video Processor RMD-V3104UInput signalsinput video signal system...BNC connectorsCD Composite video signal...
C:H/\Fu'A'ER 7. MVP MANUAL1. introductionThe multi video processor (hereafter referred to as MVP below) is equipped with a se
MVP MANUAL2. CONNECTION WITH MVP EXTERNAL COMPUTER• Refer to Chapter 4.(P.105) "External Control by MPJ RS-232C” for how to adjust the MPJ.• U
MVP MANUAL3. INSTRUCTIONS FOR USING A COMPUTER AS A TERMINAL<When the IBM-PC/AT is used>• Use commercially available communications software.•
MVP MANUAL4. OPERATING MODES1. Normal mode2.Operation modeThis mode is set when the power and reset switches are pressed.This makes the panel swit
MVP MANUAL5. Adjustment Mode • NTSC Input Board Adjustment Mode:Mode in which the adjustment commands of the NTSC input board can be executed. (Adjust
MVP MANUAL5. MVP VIDEO OUTPUT MODES• The video output formats set by the mode switches are as shown in the following table. (At shipment, the mode sw
INTRODUCTIONThank you for buying this Pioneer product.Please read through these operating instructions so you will know howto operate your
MVP MANUAL6. ADJUSTMENT FUNCTIONSMVP enables the input and output boards to be adjusted and set by connecting the external computer.
MVP MANUAL7. PICTURE FRAME ADJUSTMENT PROCEDURESAdjust the MVP picture frame as follows.(1) Connect the RS-232C cable to the MVP panel.(Refer to (P.
MVP MANUAL(3) To set the system back to 4-screen magnification [@ command]Input: @h [J] (h=8 or 9)Explanation: • For setting the system back to 4-sc
MVP MANUAL(2) To perform coarse adjustments of the picture frame [&P2, &Q2 commands]Input: &P2d2hih2ha, &Q2d2hih2ha (3Explanation:
MVP MANUAL(3) To store the picture frame data [&W command]Input : &W0, &W1Explanation : &W0 : Sets the saved values to the settings
MVP MANUAL3. To switch the image input [IFF command]Input: IFFa (3Explanation: Switches between the V IN input 4-screen enlarged display and the OPT
MVP MANUAL4. To indicate the current MVP state [SYS command]Input: SYS [J]Explanation: The current MVP state is shown when SYS (TD is input.(Example
MVP MANUAL*6 : Display of remote and manual states REMOTE MODE MANUAL MODE*7 : Slot number*8 : Type of input boardNTSC BOARD V.SCAN BOARD NO BOARD*9 :
MVP MANUAL(3) Bright compensation [BRT command]Input: BRTd HExplanation: Corrects the brightness of the NTSC input board.d : Compensation value 0
MVP MANUAL(5) Tint adjustment [TNT command]Input : TNTdid2d3(3]Explanation: Corrects the tint of the NTSC input board.did2d3 : Compensation value
PRECAUTIONS UPON USE A• Power cord precautions AThe power cord should be unplugged or plugged into the outlet by grasping the plug and
MVP MANUAL(5) To set the output to the NTSC mode [NT command](6) To set the output to standard RGB mode [NTR command](7) To set the output to the d
MVP MANUAL8. DEMO PATTERN SETTINGS AND CAUTIONSThe MVP does not have an RMD-V3216 type DEMO switch, but 2x2 enlarged screen automatic
MVP MANUAL9. INSTALLING AND REMOVING BOARDS• Be sure to turn the power off before installing and removing boards.<InstaMation procedure>© Remo
MVP MANUAL<Board layout>Lane exclusively for control boards Lane exclusively for option boards Lane exclusively for input boards Lane e
MVP MANUAL10. RMD-V3020 COMMAND REFERENCE(1) Outline of the RMD-V3020• IntroductionThe RMD-V3020 is an input board (hereafter referred to a
MVP MANUAL(2) VS board command rules0. Symbolsaaa : Command consisting of 3 alphabet lettersddd : Basic commands : Decimals between 0 to 255 consist
MVP MANUAL2. Exceptional commands• Model data commandsTBL : Displays the current model data table.TBLhh : Displays the hh model data table.M : Di
MVP MANUAL(3) Tracking adjustment [TRK command]Input : TRKd1d2d3Explanation: • d1d2d3 : Compensation data 0 to 254• Eliminates lateral vibration of
MVP MANUAL(7) B, R clamp adjustment [BLV, RLV commands]Input : BLVdid2d3, RLVdid2d3Explanation : • did2d3 : Compensation data 0 to 254• BLV : Adjus
MVP MANUAL(10) Horizontal, vertical blanking window position adjustment [HWN, VWN commands]Input : HWNdid2d3, VWNdid2d3Explanation : • did2d3 :Compe
PRECAUTIONS UPON USE A> Ventilation (Install in a well-ventilated room)^The rear panel is equipped with fans to prevent the internal temp
MVP MANUAL(12) Full dot number compensation [HFD command]Input : HFDdddExplanation : • d1d2d3:Compensation data 0 to 254• Corrects the preset sampl
MVP MANUAL(15) Vertical compression filter conversion rate input [LCV command]Input : LCVdid2d3d4Explanation : • did2=00 to 15 (Add 0 before all num
MVP MANUAL(18) To select preset model [M command]Input :Explanation : •Mhih2Refer to "VS Board Model Selection” described later for the VS board
MVP MANUAL(19) Model fresh [F command]Input : Fhih2Explanation : • Sets back to the model data preset at shipment. Model data No.hi000000000012259h2
MVP MANUAL(21) Model table reference [TBL command]Input : TBLhih2Explanation : hh model data No. (Refer to the M command for the model data No.)• Di
MVP MANUALThe relative address and data are as follows.However, relative addresses 20 to 3F are the system reservation range.RelativeADDRData Contents
MVP MANUAL(23) Vertical frequency input [VFQ command]Input : VFQdid2d3.d4d5d6Explanation :• Directly changes the horizontal frequency of the
MVP MANUAL11. MODE 99The VS board contains preset data for autolocking 9 computer main models at shipment.However, looking at the recent PC mar
MVP MANUAL12. VS BOARD MODEL SELECTION99 data as it is.DescriptionWith the VS board, first the input PC frequency and full line number a
MVP MANUAL14. SELECTING THE SYNC SIGNALWhen adjusting the VS board, care must be taken regarding the relation of the priority order o
FEATURESHigh quality signal processingCross-color and dot disturbance are reduced by the motion-compensative type 3D Y/C separation. Vertical resoluti
TYPICAL SETUP (AN EXAMPLE OF A SETUP THAT IS POSSIBLE USING THE FACTORY PRESETS)There are connections between this unit and displays.® Connect the Y/C
CONTROLS AND CONNECTORSFRONT PANEL0 POWER indicatorLights when the power is ON.@ POWER switchPress to switch the power ON/OFF.7<ARE1336>En
CONTROLS AND CONNECTORSREAR PANEL3(p (?) ® ® ® ®(T) (8)(D (ja (Q)È1mmÔ□ Si3UTi OUTPUTR H/C8) Pt (ITOI IVBBfI /iSsV GUnV OUTS "[Ml E EV OUT3
Signal nameFG..............Frame GroundTxD.........Transmitted DataRxD......
Comments to this Manuals